Our crew installs blown-in attic insulation in North York, and we're about 2 km from the middle of it. North York takes in our pages for Bayview Village, Willowdale, Don Mills, York Mills, Fairview, Hillcrest Village, Parkwoods, Bathurst Manor, Victoria Village and Northwood Park. The job goes the same way in every one of them, starting at the attic floor.

First, the attic floor

In the post-war years, the late 1940s and 1950s, a housing shortage led North York to develop as a suburb of Toronto. By the 1950s and 1960s, North York resembled many other sprawling North American suburbs.

That tells us when a lot of the area was built. It doesn't tell us what is in your attic. Over the decades insulation gets added, pulled out and walked on, so the only way to know is to look. If your house has an attic hatch, you can check it yourself with a flashlight and a tape measure: see whether the insulation sits above or below the tops of the ceiling joists, and measure how deep it is.

Whatever we find, our order of work stays the same. There are three steps, and each one has to be finished before the next one starts.

Sealing the ceiling

First we seal the attic floor. That means the gaps around light boxes, plumbing stacks and wiring holes, and the top plates of interior walls, where warm, moist house air leaks up into the attic. Insulation slows heat. It does not stop air, so the sealing has to come first.

Baffles at the eaves

Then we fit baffles at the eaves. A baffle holds a clear channel between the soffit vents and the roof deck, so outside air can still move through the attic once the new layer is in. Without baffles, loose insulation drifts into the soffits and blocks them.

The blown-in layer

Last, our crew installs blown-in insulation to full depth. We staple depth rulers to the joists before we start, so after we leave you can stand at the hatch and read the level for yourself.

Our North York neighbourhood pages

Each neighbourhood below has its own page, and every one gets the same sequence: seal, baffle, then blow in.

Our Bayview Village page starts where every job does, at the attic floor. On the Willowdale page we cover the depth check you can do from your own hatch. Don Mills has its own page on clearing the eaves before anything is blown in. For York Mills, the page walks through air sealing at the top plates.

The Fairview page explains what the depth rulers tell you after we leave. Our Hillcrest Village page covers when old insulation has to come out first. In Parkwoods the order of work is the same, and the page sets it out step by step.

Bathurst Manor gets the same check at the soffit vents before the new layer goes down. The Victoria Village page looks at sealing around light boxes and plumbing stacks. Last, Northwood Park has a page on blowing the attic in to full depth.

When old insulation has to come out

Wet or rodent-damaged insulation comes out before anything new is added. Damp fibreglass or cellulose loses most of its value and keeps the wood around it wet. Insulation that animals have nested in is packed down and soiled, and new material blown on top would sit over the same problem.

If your attic has either, we start with attic insulation removal, then move on to sealing, baffles and the new layer in the usual order. If the insulation is dry and clean, it can usually stay, and we blow the new layer over it.

If we find vermiculite, we stop. We leave it undisturbed and recommend having a qualified lab or abatement firm test it before any work goes ahead.

Removal, foam and rebates in North York

Besides blown-in work, we do three other jobs here. Each one depends on what your house has, and that is something we see from the hatch, not from the street.

Removal comes first if the old layer is wet or damaged, as described above. Spray foam attic insulation fits where loose fill can't go: if your house has a cathedral ceiling with no attic space above it, or open rim joists in the basement, closed-cell foam seals and insulates those spots in one pass.

Rebates and cost are the fourth part. Programs change, and whether your house qualifies is for the program to confirm before the work starts, so we put the scope in a written estimate you can take to them. Everything we do is listed on our home page.

Neighbourhoods we cover in North York

About North York: North York, ON on Wikipedia ยท North York on Google Maps

FAQ

Insulation questions from North York

We cover all ten North York neighbourhoods with their own page: Bayview Village, Willowdale, Don Mills, York Mills, Fairview, Hillcrest Village, Parkwoods, Bathurst Manor, Victoria Village and Northwood Park. We also work in East York, Leaside, Old Toronto and Lawrence Park. We're about 2 km from the middle of North York.

Blown-in attic insulation goes in last, after the ceiling is air sealed and baffles are set at the eaves. Sealing stops house air leaking into the attic, and the baffles keep the soffit vents open to the roof deck. Then our crew blows the insulation in to full depth against depth rulers stapled to the joists.

Yes, wet attic insulation comes out before any new insulation goes in. Wet material insulates poorly and holds moisture against the ceiling joists and top plates. Once it is out and the attic is dry, we seal, fit baffles and blow in the new layer.

Get a quote

Arrange an insulation visit in North York

Call (437) 525-3774 or send the form. We'll look in your attic, tell you what it needs and give you a written estimate.

Call Text Quote